Tag Archives: vSphere

Example VMware vNetworking Design for IP Storage

Posted on by
1

On a regular basis, I am being asked how to configure vNetworking to support environments using IP Storage (NFS / iSCSI).

The short answer is, as always, it depends on your requirements, but the below is an example of a solution I designed in the past.

Requirements

1. Provide high performance and redundant access to the IP Storage (in this case it was NFS)
2. Ensure ESXi hosts could be evacuated in a timely manner for maintenance
3. Prevent significant impact to storage performance by vMotion / Fault Tolerance and Virtual machines traffic
4. Ensure high availability for ESXi Management / VMKernel and Virtual Machine network traffic

Constraints

1. Four (4) x 10GB NICs
2. Six (6) x 1Gb NICs (Two onboard NICs and a quad port NIC)

Note: So in my opinion the above NICs are hardly “constraining” but still important to mention.

Solution

Use a standard vSwitch (vSwitch0) for ESXi Management VMKernel. Configure vmNIC0 (Onboard NIC 1) and vmNIC2 (Quad Port NIC – port 1)

ESXi Management will be Active on vmNIC0 and vmNIC2 although it will only use one path at any given time.

Use a Distributed Virtual Switch (dvSwitch-admin) for IP Storage , vMotion and Fault Tolerance.

Configure vmNIC6 (10Gb Virtual Fabric Adapter NIC 1 Port 1) and vmNIC9 (10Gb Virtual Fabric Adapter NIC 2 Port 2)

Configure Network I/O with NFS traffic having a share value of 100 and vMotion & FT will each have share value of 25

Each VMKernel for NFS will be active on one NIC and standby on the other.

vMotion will be Active on vmNIC6 and Standby on vmNIC9 and Fault Tolerance vice versa.

vNetworking Example dvSwitch-Admin

Use a Distributed Virtual Switch (dvSwitch-data) for Virtual Machine traffic

Configure vmNIC7 (10Gb Virtual Fabric Adapter NIC 1 Port 2) and vmNIC8 (10Gb Virtual Fabric Adapter NIC 2 Port 1)

Conclusion

While there are many ways to configure vNetworking, and there may be more efficient ways to achieve the requirements set out in this example, I believe the above configuration achieves all the customer requirements.

For example, it provides high performance and redundant access to the IP Storage by using two (2)  VMKernel’s each active on one 10Gb NIC.

IP storage will not be significantly impacted during periods of contention as Network I/O control will ensure in the event of contention that the IP Storage traffic has ~66% of the available bandwidth.

ESXi hosts will be able to be evacuated in a timely manner for maintenance as

1. vMotion is active on a 10Gb NIC, thus supporting the maximum 8 concurrent vMotion’s
2. In the event of contention, worst case scenario vMotion will receive just short of 2GB of bandwidth. (~1750Mb/sec)

High availability is ensured as each vSwitch and dvSwitch has two (2) connections from physically different NICs and connect to physically separate switches.

Hopefully you have found this example helpful and for a example Architectural Decision see Example Architectural Decision – Network I/O Control for ESXi Host using IP Storage

Example Architectural Decision – Network Failover Detection Policy

Posted on by
Reply

Problem Statement

What is the most suitable network failover detection policy to be used on the vSwitch or dvSwitch NIC team/s in an environment which uses IP storage and has only 2 physical NICs per vSwitch or dvSwitch?

Assumptions

1. vSphere 5.0 or greater
2. Storage is presented to the ESXi hosts is NFS via Multi Switch Link Aggregation
3. A maximum of 2 physical NICs exist per dvSwitch
4. Physical Switches support “Link state tracking”

Motivation

1. Ensure a reliable network failover detection solution
2. Ensure Multi switch link aggregation can be used for IP storage

Architectural Decision

Enable “Link state tracking” on the physical switches and Use “Link Status”

Justification

1. To work properly, Beacon Probing requires at least 3 NICs for “triangulation”  otherwise a failed link cannot be determined.
2.“Link state tracking” can be enabled on the physical switch to report upstream network failures where an “edge” & “core” network topology is used, therefore preventing the link status from being OK when traffic cannot reach the destination due to an upstream failure
3. Beacon Probing and the “route based on IP hash” network load balancing option is not compatible which prevents a single VMKernel being able to use multiple interfaces for IP storage traffic

Implications

1. Link state tracking needs to be supported and enabled on the physical switches

Alternatives

1. Use “Beacon Probing”

Example Architectural Decision – Virtual Machine swap file location

Posted on by
1

Problem Statement

When using shared storage where deduplication is utilized along with an array level snapshot based backup solution, what can be done to minimize the wasted capacity of snapping transient files in backups and the CPU overhead on the storage controller having to attempt to deduplicate data which cannot be deduped?

Assumptions

1. Virtual machine memory reservations cannot be used to reduce the vswap file size

Motivation

1. Reduce the snapshot size for backups without impacting the ability to backup and restore
2. Minimize the overhead on the storage controller for deduplication processing
3. Optimize the vSphere / Storage solution for maximum performance

Architectural Decision

1. Configure the HA swap file policy to store the swap file in a datastore specified by the host.
2. Create a new datastore per cluster which is hosted on Tier 1 storage and ensure deduplication is disabled on that volume
3. Configure all Host’s within a cluster to use the same specified datastore for vswap files
4. Ensure the new datastore is not part of any backup job

Justification

1. With minimal added complexity, backup jobs now exclude the VM swap file which reduces the backup size by the total amount of vRAM assigned to the VMs within the environment
2. As the vswap file is recreated at start up, loosing this file has no consequence
3. Decreasing Tier 1 storage requirements
4. The storage controller will not waste CPU cycles attempting to dedupe data which will not dedupe
5. Setting high percentages of memory reservation may impact the overcommitment in the environment where specifying a datastore for vswap reduces overhead without any significant downside

Implications

1. A datastore will need to be created for swapfiles
2. HA will need to be configured to store the swap file in a datastore specified by the host
3. The host (via Host Profiles) will need to be configured to use a specified datastore for vswap
4. vMotion performance will not be impacted where a VM is vMotion’d between two hosts that do not have a common vswap datastore as one datastore per cluster will be used for vswap files
5. The datastore will need to be sized to take into account the total vRAM assigned to VMs within the cluster

Alternatives

1. Set Virtual machine memory reservations of 100% to eliminate the vswap file
2. Store the swap file in the same directory as the virtual machine and accept the overhead on backups & dedupe
3. Use multiple datastores for vSwap across the cluster and accept the impact on vMotion